Netw204: Assignment 4, Link-State Routing and Ospf

In: Computers and Technology

Submitted By tonynunez55
Words 655
Pages 3
NETW204: Assignment 4, Link-state Routing and OSPF (50 points)

Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox.

NAME | Jose Antonio Nunez |

| Term | Definition | 1 | An OSPF network | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | Is an OSPF router located between OSPF autonomous system networks and non-OSPF networks. | 3 | Backup Designated Router (BDR) | Is a router that becomes the Designated Router if the DR fails. | 4 | Database Description (DBD) | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | Is an OSPF router that controls the routes of LSA’s or LSU’s. It helps maintain link state updates to other routers in the network. | 6 | DRothers | Is neither a DR, nor a BDR. They are other routers in the OSPF network. | 7 | Flapping link | Is when an advertised route between two nodes alternates back and forth. This creates a link state that cycles between up and down. | 8 | The highest IP address of an active router interface. | Router ID for an OSPF router if no loopbacks are configured? | 9 | link-state acknowledgment (LSAck) | This is an acknowledgement that an LSA or LSU packet has been received. | 10 | link-state advertisements (LSA) | Is a broadcasted link-state packet that contains link state information. This is helps maintain routing information. | 11 | Link-state Request (LSR) | Asks for more…...

Similar Documents

Ospf for Traffic Routing

...OSPF for Traffic Routing Robert Collazo Rasmussen College Author Note This research is being submitted on August 30, 2013, for Christine Stagnetto-Zweig’s N235/CET2629 Section 02 Cisco Networking Fundamentals and Routing course. OSPF for Traffic Routing The OSPF dynamic routing protocol is probably the most popular LAN routing protocol today. OSPF can scale to the largest LANs but can also start out small. With OSPF, every router has its own unique "picture" (topology map) of the network. Routers use "HELLO" packets to periodically check with routers to ensure they are still there. Every router in OSPF is identified with a "router ID". The router ID can be manually entered or OSPF will automatically choose the IP address with the highest number. To configure OSPF, Set the bandwidth on your interfaces using the bandwidth command Router (config-if)# bandwidth XX (where XX signifies the bandwidth of the WAN connection). Router (config)# router ospf {process-ID#} Next, instruct the router to advertise the networks that are directly linked to it by entering network statements with the area ID number for that network, Router (config-router)# network {X.X.X.X} {Y.Y.Y.Y} area {z} X.X.X.X = Network ID of Network Y.Y.Y.Y = the wildcard mask for the network (the wildcard mask is the inverse mask of the subnet mask). Z = the area ID number (For small networks, this can always be zero (0) but for larger networks, the area IDs need to be properly planned as all routing......

Words: 374 - Pages: 2

Ospf for Traffic Routing

...OSPF for Traffic Routing Robert Collazo Rasmussen College Author Note This research is being submitted on August 30, 2013, for Christine Stagnetto-Zweig’s N235/CET2629 Section 02 Cisco Networking Fundamentals and Routing course. OSPF for Traffic Routing The OSPF dynamic routing protocol is probably the most popular LAN routing protocol today. OSPF can scale to the largest LANs but can also start out small. With OSPF, every router has its own unique "picture" (topology map) of the network. Routers use "HELLO" packets to periodically check with routers to ensure they are still there. Every router in OSPF is identified with a "router ID". The router ID can be manually entered or OSPF will automatically choose the IP address with the highest number. To configure OSPF, Set the bandwidth on your interfaces using the bandwidth command Router (config-if)# bandwidth XX (where XX signifies the bandwidth of the WAN connection). Router (config)# router ospf {process-ID#} Next, instruct the router to advertise the networks that are directly linked to it by entering network statements with the area ID number for that network, Router (config-router)# network {X.X.X.X} {Y.Y.Y.Y} area {z} X.X.X.X = Network ID of Network Y.Y.Y.Y = the wildcard mask for the network (the wildcard mask is the inverse mask of the subnet mask). Z = the area ID number (For small networks, this can always be zero (0) but for larger networks, the area IDs need to be properly planned as all routing......

Words: 347 - Pages: 2

Routing Protocol

...EIGRP and OSPF Comparison For Client Sponsor Prepared By Scott Hogg Project Number 02 Date March 14, 2002 |Distribution List | |Name |Title/Duties |Company | |John Vogt-Nilsen |Manager – Network Operations | | |Sammy Hutton |Principal Systems Analyst | | |Scott Hogg |Principal Consultant |Lucent | |Phil Colon |Managing Consultant |Lucent | |Revision History | |Version |Date |Author |Comments | |1.0 |03/14/2002 |Scott Hogg |Initial Draft | | | | | ......

Words: 8531 - Pages: 35

Netw204

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | | Term | Definition | 1 | Area Border Router (ABR) | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | A router that exchanges routing information with routers belonging to other AS (Autonomous System) | 3 | Backup Designated Router (BDR) | The BDR is used to provide redundancy in broadcast networks which are utilizing the OSPF (Open Shortest Path First) routing protocol | 4 | Database Description (DD) | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | OSPF router that generates LSAs for a multiaccess network and has other special responsibilities in running OSPF | 6 | DRothers | Routers that are not DR or BDR | 7 | Flapping link | | 8 | Highest IP | Router ID for an OSPF router if no loopbacks are configured? | 9 | link-state acknowledgment (LSAck) | Routing problem where an advertised route between two......

Words: 569 - Pages: 3

Week 4

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME Johnetta Stewart Term Definition 1 ABR Attaches to multiple areas, maintains separate link-state databases for each area it is connected to, and routes traffic destined for or arriving from other areas 2 Autonomous System Boundary Router (ASBR) The OSPF router located between an OSPF autonomous system network and a non-OSPF network. ASBRs run both OSPF and another routing protocol, such as RIP. ASBRs must reside in a non-stub OSPF area. 3 Backup Designated Router (BDR) A router that becomes the designated router if the current designated router fails. The BDR is the OSPF router with the second-highest priority at the time of the last DR election. 4 Contains an abbreviated list of the sending router’s link-state database and is used by receiving routers to check against the local link-state database 5 Designated Router (DR) OSPF router that generates LSAs for a multiaccess network and has other special responsibilities in running OSPF. Each multiaccess OSPF network that has at least two attached routers has a designated router that is elected by the OSPF Hello protocol ......

Words: 711 - Pages: 3

Netw204: Assignment 4, Link-State Routing and Ospf

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | | Term | Definition | 1 | OSPF- Open Shortest Path First | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | The OSPF router located between an OSPF autonomous system network and a non-OSPF network. ASBRs run both OSPF and another routing protocol, such as RIP. ASBRs must reside in a non-stub OSPF area. | 3 | Backup Designated Router (BDR) | A router that becomes the designated router if the current designated router fails. The BDR is the OSPF router with the second-highest priority at the time of the last DR election. | 4 | Database Description packets (DBD) | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | The designated router enables a reduction in the number of adjacencies required on a multiaccess network, which in turn reduces the amount of routing protocol traffic and the size of the topological......

Words: 524 - Pages: 3

Netw204: Assignment 4,

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | | Term | Definition | 1 | Area Border Router (ABR) | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | The OSPF router located between an OSPF autonomous system network and a non-OSPF network. ASBRs run both OSPF and another routing protocol, such as RIP. ASBRs must reside in a non-stub OSPF area. | 3 | Backup Designated Router (BDR) | A router that becomes the designated router if the current designated router fails. The BDR is the OSPF router with the second-highest priority at the time of the last DR election. | 4 | Database Description (DBD) | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | OSPF router that generates LSAs for a multi-access network and has other special responsibilities in running OSPF. Each multi-access OSPF network that has at least two attached routers has a designated router that is......

Words: 527 - Pages: 3

Netw204 Assignment 3

...NETW204: Assignment 2 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | Distance Vector Routing Protocols | Question | Answer | 1 | What does RIP stand for? | Routing Information Protocol | 2 | What metric does RIP use for Path Selection? | Rip uses the hop count metric in order to determine the best path which uses the least number of hop counts. | 3 | If the metric used by RIP exceeds this value for a route it is considered unreachable, effectively making this value appear to be infinity to RIP? | 16 | 4 | How often does RIP send updates by default (update timer)? | Every 30 seconds. | 5 | What are the main differences between RIPv1 and RIPv2? | The primary difference between RIPv1 and v2 is that v2 is classless. This means the RIPv2 incorporates the subnet mask in its advertisement. | 6 | What is convergence and why is it important? | Convergence provides automatic mapping and integration of IT resources available to the user. | 7 | Is RIP considered to be a fast or slow converging protocol? | Slow | For the simple 3 router network (Figure 1), fill in the information that would be in each router’s routing table once the network has converged (see example in Chapter 4, pages 192-193). Figure 1 Questions 8-22 (15 points – first one provided) | R1 | | | | HQ | | | | R3 | ...

Words: 904 - Pages: 4

Network 204 Assignment 4

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | Chad White | | Term | Definition | 1 | ABR | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | Routers that have at least one interface attached to an external internetwork (another autonomous system [AS]), such as a non-OSPF network. ASBRs can import non- OSPF network information to the OSPF network and vice versa; this process is called route redistribution. | 3 | Backup Designated Router (BDR) | Used to provide redundancy in broadcast networks which are utilizing the OSPF | 4 | DBD | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | A router that informs end nodes of the existence and identity of other routers. | 6 | DRothers | Routers that are not a dr or bdr. they are the routers in the ospf network. | 7 | Flapping link | A link which cycles between up and down. | 8 | Highest active IP | Router ID for an OSPF...

Words: 638 - Pages: 3

Unit 5 Assignment 5.1 Eigrp vs Ospf

...Unit 5 Assignment 1: Cisco Networks EIGRP versus OSPF EIGRP: Enhanced Interior Gateway Routing Protocol Is another routing protocol just like RIP and OSPF. EIGRP converges very quickly and it takes about the same time or not less than OSPF takes to converge, but without the negatives of OSPF. EIGRP’s benefit requires much less processing time, memory and less design than say OSPF. The downside with EIGRP is that it is Cisco-proprietary, so if an internet work areas uses non-Cisco routers it cannot be used on those routers. EIGRP is neither distance-vector nor link-state. Sometimes Cisco refers to EIGRP as an enhanced distance vector protocol but in some cases calls it a balanced hybrid routing protocol. EIGRP has some similarities to routing protocols but the differences far outweigh them. OSPF: Open Shortest Path First Is a link-state routing protocol for Internet Protocol (IP) networks. It uses a link state routing algorithm and falls into the group of interior routing protocols, operating within a single autonomous system (AS). It is defined as OSPF Version 2 in RFC 2328for IPv4. The updates for IPv6 are specified as OSPF Version 3 in RFC 5340 . OSPF is perhaps the most widely used interior gateway protocol (IGP) in large enterprise networks. IS-IS, another link-state dynamic routing protocol, is more common in large service provider networks. The most widely used exterior gateway protocol is the Border Gateway Protocol (BGP), the principal routing protocol between......

Words: 269 - Pages: 2

Netw204 Assignment 1

...NETW204: Assignment 1 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | Router Configuration Exercise (5 points) When configuring a router, there are certain basic tasks performed, * Naming the router * Setting passwords * Configuring interfaces * Configuring a banner * Saving changes on a router * Verifying basic configuration and router operations | Question | Answer | 1 | The first prompt is _______ mode and will allow you to view the state of the router. | user | 2 | What major limitation does this mode have? | User mode will not allow you to modify its configuration. | 3 | What does the router prompt look like for this mode? | router> | 4 | The enable command is used to enter the privileged mode. What is the major difference between this mode and user mode? | The enable command is used to enter privileged EXEC mode and allows you to make changes to the configuration of the router. | 5 | What does the router prompt look like for this mode? | router# | Basic Configuration Tasks (18 points) The table below lists the basic router configuration tasks in the left column. Fill in the blanks in the right column with the correct command syntax for each of the tasks. | Configuration Task | Command Syntax | Answer | 6 | Naming the router | Router(config)# |......

Words: 1189 - Pages: 5

Netw204 Assignment 1

...NETW204: Assignment 1 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | Jessica Brisbane (Brown) | Router Configuration Exercise (5 points) When configuring a router, there are certain basic tasks performed, * Naming the router * Setting passwords * Configuring interfaces * Configuring a banner * Saving changes on a router * Verifying basic configuration and router operations | Question | Answer | 1 | The first prompt is _______ mode and will allow you to view the state of the router. | userEXEC | 2 | What major limitation does this mode have? | No configurations can be performed to the router. | 3 | What does the router prompt look like for this mode? | > | 4 | The enable command is used to enter the privileged mode. What is the major difference between this mode and user mode? | The major difference between user mode and privileged mode is that no configuration can be performed in user mode. | 5 | What does the router prompt look like for this mode? | # | Basic Configuration Tasks (18 points) The table below lists the basic router configuration tasks in the left column. Fill in the blanks in the right column with the correct command syntax for each of the tasks. | Configuration Task | Command Syntax | Answer | 6 | Naming the router | Router(config)# |......

Words: 1150 - Pages: 5

Netw204 Assignment 1

...NETW204: Assignment 1 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | Router Configuration Exercise (5 points) When configuring a router, there are certain basic tasks performed, * Naming the router * Setting passwords * Configuring interfaces * Configuring a banner * Saving changes on a router * Verifying basic configuration and router operations | Question | Answer | 1 | The first prompt is _______ mode and will allow you to view the state of the router. | User Exec | 2 | What major limitation does this mode have? | The User mode of a router allows you to view the state of the router, but does not allow you to modify the router's configuration. | 3 | What does the router prompt look like for this mode? | > | 4 | The enable command is used to enter the privileged mode. What is the major difference between this mode and user mode? | In Privileged exec mode, a user can enter some commands to modify the router’s configuration. All commands available in User mode are a subset of Privileged mode, but Privileged mode does not have as many as Global Config mode. | 5 | What does the router prompt look like for this mode? | # | Basic Configuration Tasks (18 points) The table below lists the basic router configuration tasks in the left column. Fill in the blanks......

Words: 1157 - Pages: 5

Netw204 Assignment 4

...NETW204: Assignment 4, Link-state Routing and OSPF (50 points) Fill in the blanks below with either the term defined or the definition for the terms listed. Each answer is worth 2 points each, 25 questions X 2 = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | | | Term | Definition | 1 | Area Border Router or ABR | Attaches to multiple areas, maintains separatelink-state databases for each area it is connectedto, and routes traffic destined for or arriving fromother areas | 2 | Autonomous System Boundary Router (ASBR) | The OSPF router located between an OSPF autonomous system network and a non-OSPF network. ASBRs run both OSPF and another routing protocol, such as RIP. ASBRs must reside in a non-stub OSPF area. | 3 | Backup Designated Router (BDR) | A router that becomes the designated router if the current designated router fails. The BDR is the OSPF router with the second-highest priority at the time of the last DR election. | 4 | Database Description | Contains an abbreviated list of the sendingrouter’s link-state database and is used by receiving routers to check against the local link-state database | 5 | Designated Router (DR) | OSPF router that generates LSAs for a multiaccess network and has other special responsibilities in running OSPF. Each multiaccess OSPF network that has at least two attached routers has a designated router that is elected by the...

Words: 635 - Pages: 3

Netw204 Assignment 1

...NETW204: Assignment 1 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME Router Configuration Exercise (5 points) When configuring a router, there are certain basic tasks performed, • Naming the router • Setting passwords • Configuring interfaces • Configuring a banner • Saving changes on a router • Verifying basic configuration and router operations Question Answer 1 The first prompt is _______ mode and will allow you to view the state of the router. User Mode 2 What major limitation does this mode have? Allows you to view the router but not any modifications 3 What does the router prompt look like for this mode? Router> 4 The enable command is used to enter the privileged mode. What is the major difference between this mode and user mode? This mode allows you to configure or modify the router. 5 What does the router prompt look like for this mode? Router>enable router#   Basic Configuration Tasks (18 points) The table below lists the basic router configuration tasks in the left column. Fill in the blanks in the right column with the correct command syntax for each of the tasks. Configuration Task Command Syntax Answer 6 Naming the router Router(config)# hostname (name) 7 Setting passwords Router(config)# enable secret (password) 8 Router(config)# line con......

Words: 1130 - Pages: 5